10 Best Miter Gauges

Product Highlights

arrow_forwardThe Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.

arrow_forwardThe .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.

arrow_forwardThe head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.

arrow_forwardMade from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.

arrow_forwardBoth ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.

Product Highlights

arrow_forwardIf you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs.

arrow_forwardThe .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.

arrow_forwardTo adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two ¼” x ½” slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8” from the base of the miter gauge head.

arrow_forwardThe head is mounted to a solid steel miter bar that measure 18” in length and is .354” thick by .730” wide. Standard miter slots are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.

arrow_forwardThe steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through. If your saw does not have a “T” slot, you can remove the disc. The steel miter bar is also equipped with spring loaded, adjustable plungers on the side of the bar. The plungers can be adjusted with the provide hex key wrench in or out to provide you with the ideal fit.

Product Highlights

arrow_forwardWhen cutting mitered angles with your table saw you always want to make sure that have enough support of your stock when feeding it through the blade. The table saw blade is rotating toward you at a high rate of speed and if your workpiece moves to the side, the result can be scary and downright dangerous. With the help of a miter gauge and with our Aluminum Miter Fence secured to it, you will have full support all the way up to the blade on most of your miter angle cuts.

arrow_forwardThe Aluminum Miter Fence has been cut at 45 degrees on both ends of the fence. Doing this allows you to get as close to the blade as possible so your workpiece is fully supported throughout the cutting process. Straight cut or 90 degree cut fences have a large gap between the fence and the blade because it can not get as close with the straight cut ends on the fence.

arrow_forwardMany times when we make miter cuts on our table saw, we need 2 or more pieces that are the exactly same length. While using the included measuring tapes that are included are pretty good at this, we have also included a handy flip stop that locks into any location along the length of the fence. This allows you to make repetitive length cuts without worrying if the pieces will end up the same. The flip stop can can simply be flipped it up and out of your way when not in use.

arrow_forwardThe Fulton Aluminum Miter Fence is made from one, solid piece of extruded aluminum and has the exact same size track on the top of the fence as there is on the bottom. On the back, there is an offset track for mounting the fence to a miter gauge.

arrow_forwardThe fence can be mounted to low profile miter gauges or standard profile miter gauges simply by flipping the fence over to accommodate your miter gauge. This fence will fit most available after market and factory table saw miter gauges, however some modification may be required. Full color installation instructions are included.

Product Highlights

arrow_forwardFactory Calibration. Guaranteed out of the box to .003 accuracy of 6-inches

arrow_forwardGauge head is CNC machine perfectly square to the bar and table ( no stampings)

arrow_forwardVernier scale allows fast, 1/10th-degree angle adjustments. Our extremely straight 24 inch (610mm) anodized-aluminum bar is 3/8 inch(9.5mm) thick by 3/4 inch(19mm) wide and features five bar adjusters that you can use to eliminate “play” in the miter slot with the turn of a screwdriver

arrow_forwardMicroadjuster allows additional angle adjustment to 1/100th degree

arrow_forwardPositive stops at 0, 10, 22-1/2, 30 and 45-degrees; limited lifetime warranty

Product Highlights

arrow_forwardEngraved stainless steel primary scale for precision accuracy

arrow_forward41 laser cut V-stops for extreme accuracy at all popular angles

arrow_forwardPatented GlideLOCK miter bar with 6 expansion points for quick repeats

arrow_forward18- to 31-inch telescoping incremental miter fence for handling a variety of stock widths

arrow_forwardINCRA Flip Shop Stop-Fence Positioner for optimal mitering accuracy

Product Highlights

arrow_forwardCOMPLETE POCKET HOLE JIG SYSTEM - Jig kit includes: pocket hole jig with clamp, #32 3/8 In. Step Drill Bit (replaceable), 3/8 in. steel stop collar, Hex wrench 6 in. square drive bit, 24 coarse square drive screws, 24 fine square drive screws, 24 wooden pocket hole plugs, Hard plastic carrying case.

arrow_forwardACCURATE- this jig creates flush, corner and angle pocket hole joints for leg-and-rail connections, building face frame cabinets, sneaking screws into tight spots, and fastening picture frames with unlimited applications

arrow_forwardEASY TO USE- DIYers and expert craftsmen turn to this jig kit to build their woodworking projects. First, use the jig to drill steeply pitched counter bores in one joint member; then, drive self-tapping screws (without pilot holes) into the other member

arrow_forwardVERSATILE- built to be portable or bench mounted and designed with a built-in clamping system

arrow_forwardCOMPLIANT- with Forest Stewardship Council (FSC)

Product Highlights

arrow_forwardMiter Protractor "O" ring insures smooth and precise operation, takes error-prone calculations out of the process of miter cuts.

arrow_forwardDirect read from the work to your miter saw with two easy to read scales

arrow_forwardEasy-to use tool has two laser engraved scales

arrow_forwardProtractor saves time and reduces waste